View MC10E451_29369.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
6 Bit D Register Differential Data and Clock
The MC10E/100E451 contains six D-type flip-flops with single-ended outputs and differential data inputs. The common clock input is also differential. The registers are triggered by a positive transition of the positive clock (CLK) input. A HIGH on the Master Reset (MR) input resets all Q outputs to LOW. The VBB output is intended for use as a reference voltage for single-ended reception of ECL signals to that device only. When using for this purpose, it is recommended that VBB is decoupled to VCC via a 0.01F capacitor. The differential input structures are clamped so that the inputs of unused registers can be left open without upsetting the bias network of the device. The clamping action will assert the D and the CLK sides of the inputs. Because of the edge triggered flip-flop nature of the device simultaneously opening both the clock and data inputs will result in an output which reaches an unidentified but valid state. Note that the input clamps only operate when both inputs fall to 2.5V below VCC.
MC10E451 MC100E451
6-BIT D REGISTER DIFFERENTIAL DATA AND CLOCK
* * * * * *
Differential Inputs: Data and Clock VBB Output 1100MHz Min. Toggle Frequency Asynchronous Master Reset Extended 100E VEE Range of - 4.2V to - 5.46V 75k Input Pulldown Resistors
D5 25 CLK VBB CLK VEE MR NC D0 26 27 28 1 2 3 4 5 6 7 8 9 10 11 D4 D4 D R D5 D5 CLK CLK MR VBB D R Q5 D5 24 D4 23 D4 22 D3 21 D3 20 VCCO 19 18 17 16 Q5 Q4 VCC Q3 VCCO Q2 Q1 D3 D3 D R Q4 D2 D2 D R Q3 D1 D1 D R Q2 D0 D0 FN SUFFIX PLASTIC PACKAGE CASE 776-02
LOGIC DIAGRAM
D R Q1 Q0
Pinout: 28-Lead PLCC (Top View)
15 14 13 12
D0 D1 D1 D2 D2 VCCO Q0 * All VCC and VCCO pins are tied together on the die.
PIN NAMES
Pin D0 - D5 D0 - D5 CLK CLK MR VBB Q0 - Q5
12/93
Function +Data Input - Data Input +Clock Input - Clock Input Master Reset Input VBB Output Data Outputs
(c) Motorola, Inc. 1996
2-1
REV 2
MC10E451 MC100E451
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol VBB Characteristic Output Reference Voltage 10E 100E IIH IEE Input HIGH Current Power Supply Current 10E 100E 84 84 min -1.3 8 -1.3 8 typ max -1.2 7 -1.2 6 150 101 101 84 84 min -1.3 5 -1.3 8 25C typ max -1.2 5 -1.2 6 150 101 101 84 97 min -1.3 1 -1.3 8 85C typ max -1.1 9 -1.2 6 150 101 116 A mA Unit V Condition
VCMR Common Mode Range - 2.0 - 0.4 - 2.0 - 0.4 - 2.0 - 0.4 V 2 1. VCMR is referenced to the most positive side of the differential input signal. Normal operation is obtained when the "HIGH" input is within the VCMR range and the input swing is greater than VPP MIN and < 1.0V.
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol fMAX tPLH tPHL Characteristic Max, Toggle Frequency Propagation Delay to Output CLK (Diff) CLK (SE) MR Setup Time D Hold Time D Minimum Input Swing Reset Recovery Time Minimum Pulse Width CLK, MR Within-Device Skew Rise/Fall Times 20 - 80% 275 min 1100 475 425 425 150 250 150 750 400 100 450 800 275 600 typ 1400 650 650 600 -100 100 800 850 850 max min 1100 475 425 425 150 250 150 750 400 100 450 800 275 600 25C typ 1400 650 650 600 -100 100 800 850 850 max min 1100 475 425 425 150 250 159 750 400 100 450 800 ps ps 2 600 85C typ 1400 650 650 600 -100 ps 100 mV ps ps 1 800 850 850 ps max Unit MHz ps Condition
ts th VPP(AC) tRR tPW tSKEW tr tf
1. Minimum input voltage for which AC parameters are guaranteed. 2. Within-device skew is defined as identical transitions on similar paths through a device.
MOTOROLA
2-2
ECLinPS and ECLinPS Lite DL140 -- Rev 4
MC10E451 MC100E451
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
0.007 (0.180) U T L -M
M
B -NY BRK
M
S
N
S S
0.007 (0.180)
T L -M
N
S
D Z -L-M-
W
28 1
D X VIEW D-D G1 0.010 (0.250)
S
V
T L -M
S
N
S
A Z R
0.007 (0.180) 0.007 (0.180)
M
T L -M T L -M
S
N N
S
H
S
0.007 (0.180)
M
T L -M
S
N
S
M
S
C
E G G1 0.010 (0.250)
S
K1 0.004 (0.100) J -TSEATING PLANE
K F VIEW S 0.007 (0.180)
M
VIEW S T L -M
S
T L -M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 -- 0.025 -- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 -- 0.020 2 10 0.410 0.430 0.040 --
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 -- 0.64 -- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 -- 0.50 2 10 10.42 10.92 1.02 --
ECLinPS and ECLinPS Lite DL140 -- Rev 4
2-3
MOTOROLA
MC10E451 MC100E451
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-4
*MC10E451/D*
MC10E451/D ECLinPS and ECLinPS Lite DL140 -- Rev 4

▲Up To Search▲

Price & Availability of MC10E451

	To Download MC10E451 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .